Fretting corrosion behaviour of Ti-6Al-4V reinforced with zirconia in foetal bovine serum

J Mech Behav Biomed Mater. 2019 Dec;100:103392. doi: 10.1016/j.jmbbm.2019.103392. Epub 2019 Aug 6.

Abstract

Fretting corrosion is a critical challenge in the design of hip prosthesis used in total hip arthroplasty (THA) surgeries. Currently, the design of hip implants includes a tapered junction which introduces additional interfaces that connect different parts of the hip implant such as the femoral neck and head or stem and neck interface. Micro motions that occur under the influence of load, together with chemical changes in the host environment, make these interfaces susceptible to tribocorrosion processes, particularly fretting corrosion. Commonly used metallic biomaterials are based on stainless steels, cobalt chrome-based alloys as well as titanium and titanium alloys. Each of these materials possess some degree of limitations, particularly where tribocorrosion events are concerned. Titanium alloy Ti-6Al-4V is widely used in biomedical applications for non-bearing components of total joint arthroplasty (TJA) surgeries. Its poor wear resistance continues to remain a challenge in load-bearing joints where parts articulate against one another as in the case of modular junctions. Some of the attempts made to improve the wear properties of Ti-6Al-4V is through the incorporation of second phase particles like ceramics in its matrix to produce metal matrix composites of Ti-6Al-4V. The aim of this work is to investigate the effect of zirconia reinforcement on spark plasma sintered Ti-6Al-4V composites (zirconium oxide particles incorporated into Ti-6Al-4V matrix) on the fretting corrosion properties of Ti-6Al-4V. Fretting corrosion tests were carried out on as-sintered Ti-6Al-4V and Ti-6Al-4V with 5 and 10 wt.% ZrO2. The tests were carried out in foetal bovine serum under applied normal loads of 85 and 115 N using the cylinder-on-flat contact configuration. The evolution of OCP, dissipated energy and friction coefficient were recorded throughout the test. Microstructural analysis of the samples before fretting corrosion tests showed the presence of globular agglomerates throughout the Ti-6Al-4V matrix due to zirconia additions; the volume of the agglomerates was higher in the composites having 10 wt.% ZrO2. Ti-6Al-4V composites having zirconia additions produced a nobler OCP during fretting in foetal bovine serum, compared to pure Ti-6Al-4V. Furthermore, the fretting corrosion results showed a significant improvement in the tribocorrosion resistance of Ti-6Al-4V with 10 wt.% ZrO2 at all loads. This composition also produced the least amount of degradation. and metal ion release. Mechanical data showed that increasing the applied normal load promoted a transition from gross slip to partial slip conditions for all compositions. Partial slip was found to be prevalent at a higher normal load (drastic decrease of the dissipated energy and consequently the friction coefficient). This mechanical condition prevents a large amount of degradation.

Keywords: Biomaterials; Fretting-corrosion; Metal Matrix Composites; Ti-6Al-4V; Titanium; Zirconia.

Publication types

  • Research Support, Non-U.S. Gov't

MeSH terms

  • Alloys
  • Animals
  • Arthroplasty, Replacement, Hip / methods*
  • Biocompatible Materials / chemistry*
  • Cattle
  • Corrosion
  • Femur Neck / physiopathology
  • Humans
  • Ions
  • Microscopy, Electron, Scanning
  • Prosthesis Design
  • Prosthesis Failure
  • Serum / chemistry
  • Stress, Mechanical
  • Surface Properties
  • Titanium / chemistry*
  • Zirconium / chemistry*

Substances

  • Alloys
  • Biocompatible Materials
  • Ions
  • titanium alloy (TiAl6V4)
  • Zirconium
  • Titanium
  • zirconium oxide